IS220UCSAH1A是通用电气为Mark VI系统创建的处理器/控制器。Mark VI平台设计用于管理燃气轮机或蒸汽轮机，由GE作为Speedtronic系列的一部分发布。它具有HMI（人机界面），其软件专为运行重型涡轮机而设计，例如CIMPLICITY图形界面。
IS220UCSAH1A是作为一个单一的盒装组件，前面板允许连接通信，后边缘有两个螺钉安装，三个侧面的格栅开口允许空气流动。该控制器设计用于在机柜内进行底座安装。最多可以三个组件彼此相邻安装，以实现紧凑的布置，可轻松服务于三重冗余系统。
IS220UCSAH1A
该IS220UCSAH1A适用于 QNX 操作系统。它具有飞思卡尔8349,667 MHz处理器。该板使用额定电压为 18-36 V dc、12 瓦的电源。该板可在 0 至 65 摄氏度的温度下使用，即使在最高额定温度下也不需要风扇进行冷却。该板可用于 NFPA 1 类 2 区应用。
IS220UCSAH1A的前面板有六个母插孔连接器、一个 USB 端口和多个 LED 指示灯。 这包括前面板左侧标有“链路/操作”的 LED 指示灯，以及位于面板中间的一排标有“电源”、“启动”、“联机”、“闪存”、“直流”和“诊断”的指示灯。 插孔连接器用于以太网连接，允许电路板与其他 MKVI、MKVIe 或 EX2100 激励控制进行通信， 以及维护站和操作员站。
IS220UCSAH1A
IS220UCSAH1A is a processor/controller created by General Electric for the Mark VI system. The Mark VI platform is designed to manage gas or steam turbines and is released by GE as part of the Speedtronic series. It has an HMI (Human Machine Interface), and its software is designed specifically for running heavy-duty turbines, such as the CIMPLICITY graphical interface.
IS220UCSAH1A is a single boxed component that allows for communication on the front panel, with two screws installed on the rear edge, and grille openings on the three sides allowing for air flow. This controller is designed for base installation within the cabinet. Up to three components can be installed adjacent to each other to achieve a compact layout and easily serve triple redundant systems.
IS220UCSAH1A
This IS220UCSAH1A is suitable for the QNX operating system. It has a Freescale 8349667 MHz processor. This board uses a power supply with a rated voltage of 18-36 V dc and 12 watts. The board can be used at temperatures ranging from 0 to 65 degrees Celsius, and does not require a fan for cooling even at the highest rated temperature. This board can be used for NFPA Class 1, Zone 2 applications.
The front panel of IS220UCSAH1A has six female jack connectors, one USB port, and multiple LED indicators. This includes LED indicators labeled “Link/Operation” on the left side of the front panel, as well as a row of indicators labeled “Power”, “Start”, “Online”, “Flash”, “DC”, and “Diagnostic” located in the middle of the panel. Jack connectors are used for Ethernet connections, allowing circuit boards to communicate with other MKVI, MKVIe, or EX2100 excitation controls, as well as maintenance and operator stations.
IS220UCSAH1A
There are no reviews yet.