Vibro-meter 200-570-000-014 200-570-101-013是一个处理器模块，用于测量机器设备的振动，可以实时监测振动信号并将数据传输给VM600震动监测系统。Vibro-meter 200-570-101-013是一个温度传感器，用于测量机器设备的温度，可以实时监测温度变化并将数据传输给VM600震动监测系统 。以下是该型号的一些特征和参数：测量范围广：可以测量高达2Hz至10kHz的频率范围 。响应时间短：一般为0.2ms左右 。只能带DC 5—30V的负载，最大输出负载电流为0．5A/点，但每4点不得大于0.8A 。产品尺寸为140mm x 105mm x 40mm，重量为0.5kg 。该型号的使用温度为-10°C至+50°C，存储温度为-20°C至+85°C，相对湿度为5%至95% 。
200-570-000-014
VM600机架控制器和通信接口卡。VM600 CPUM 和 IOCN 模块化 CPU 卡和输入/输出卡是一对机架控制器和通信接口卡，可用作美捷特振动计®产品线的 VM600 机架式机械保护系统 （MPS） 和/或状态监测系统 （CMS） 的系统控制器和数据通信网关。注意：提供不同版本的 CPUx/IOCx 机架控制器和通信接口卡对，如下所示：CPUM/IOCN是带有前面板显示屏的原始版本，支持Modbus RTU/TCP或PROFINET（PNR 200-595-VVV-VVV）。CPUR/IOCR是具有机架控制器冗余并支持Modbus RTU / TCP（PNR 600-007-VVV-VVV）的版本。CPUR2/IOCR2 是一个对现场总线数据进行数学处理的版本，并支持 Modbus TCP 和 PROFIBUS DP （PNR 600-026-000-VVV）。
200-570-000-014
VM600 CPUM/IOCN 机架控制器和通信接口卡对，支持 Modbus RTU/TCP 或 PROFINET，以及前面板显示器使用以太网或 RS-4 串行连接到运行 VM8 MPSx 软件的计算机，对 VM600 机架中的保护卡（MPC232 和 AMC600）进行“一次性”配置管理前面板显示屏，用于可视化保护卡的监控输出和报警限值用于保护卡和 VM600 MPS 机架 （CPUM） 安全性的通用报警复位 （AR）VM600 系统事件和测量事件日志可通过 VM600 MPSx 软件获取。
200-570-000-014
Vibro-meter 200-570-000-014 200-570-101-013 is a processor module used to measure the vibration of machine equipment, which can monitor vibration signals in real-time and transmit data to the VM600 vibration monitoring system. Vibro-meter 200-570-101-013 is a temperature sensor used to measure the temperature of machine equipment, which can monitor temperature changes in real-time and transmit data to the VM600 vibration monitoring system. The following are some features and parameters of this model: wide measurement range: can measure frequencies up to 2Hz to 10kHz. Short response time: generally around 0.2ms. Can only carry DC 5-30V loads, with a maximum output load current of 0.5A/point, but not exceeding 0.8A every 4 points. The product size is 140mm x 105mm x 40mm, and the weight is 0.5kg. The usage temperature of this model is -10 ° C to+50 ° C, storage temperature is -20 ° C to+85 ° C, and relative humidity is 5% to 95%.
200-570-000-014
VM600 rack controller and communication interface card. The VM600 CPUM and IOCN modular CPU cards and input/output cards are a pair of rack controllers and communication interface cards that can be used as Meggitt vibration meters ® The system controller and data communication gateway for the VM600 rack mounted mechanical protection system (MPS) and/or condition monitoring system (CMS) of the product line. Note: Different versions of CPUx/IOCx rack controllers and communication interface card pairs are provided, as shown below: CPUM/IOCN is the original version with front panel display, supporting Modbus RTU/TCP or PROFINET (PNR 200-595-VVV-VVV). CPUR/IOCR is a version with rack controller redundancy and supports Modbus RTU/TCP (PNR 600-007-VVV-VVV). CPUR2/IOCR2 is a version that mathematically processes fieldbus data and supports Modbus TCP and PROFIBUS DP (PNR 600-026-000-VVV).
200-570-000-014
The VM600 CPUM/IOCN rack controller and communication interface card pair support Modbus RTU/TCP or PROFINET, as well as the front panel display using Ethernet or RS-4 serial connection to a computer running VM8 MPSx software. The protection cards (MPC232 and AMC600) in the VM600 rack are “one-time” configured to manage the front panel display, The monitoring output and alarm limits used for visualizing the protection card are universal alarm reset (AR) for card and VM600 MPS rack (CPUM) security. The VM600 system event and measurement event logs can be obtained through the VM600 MPSx software.
There are no reviews yet.