BENTLY 133388-01 超速检测模块是指在超速检测模块中控制机械元件运转的发动机，是一种补助马达间接变速装置。超速检测模块可使控制速度，位置精度非常准确，可以将电压信号转化为转矩和转速以驱动控制对象BENTLY 133388-01 超速检测模块油和水的保护超速检测模块可以用在会受水或油滴侵袭的场所，但是它不是全防水或防油的。因此，超速检测模块不应当放置或使用在水中或油侵的环境中。如果伺服电机连接到一个减速齿轮，使用超速检测模块时应当加油封，以防止减速齿轮的油进入超速检测模块的电缆不要浸没在油或水中。超速检测模块电缆确保电缆不因外部弯曲力或自身重星而受到力矩或垂直负荷，尤其是在电缆出口处或连接处。在超速检测模块移动的情况下，应把电缆就是随电机配置的那根牢固地固定到一个静止的部分相对电机。
133388-01
并且应当用一个装在电缆支座里的附加电缆来延长它，这样弯曲应力可以减到最小。电缆的弯头半径做到尽可能大。超速检测模块允许的轴端负载确保在安装和运转时加到伺服电机轴上的径向和轴向负载控制在每种型号的规定值以内。在安装一个刚性联轴器时要格外小心，特别是过度的弯曲负载可能导致轴端和轴承的损坏或磨损。最好用柔性联轴器，以便使径向负载低于允许值，此物是专为高机械强度的超速检测模块设计的。关于允许轴负载。超速检测模块安装注意在安装拆卸耦合部件到超速检测模块轴端时，不要用锤子直接敲打轴端。锤子直接敲打轴端，伺服电机轴另一端的编码器要被敲坏竭力使轴端对齐到最佳状态对不好可能导致振动或轴承坏。
133388-01
BENTLY 133388-01 overspeed detection module refers to the engine that controls the operation of mechanical components in the overspeed detection module, and is a supplementary motor indirect transmission device. The overspeed detection module can control speed and position accuracy very accurately, and can convert voltage signals into torque and speed to drive the control object BENTLY 133388-01. The overspeed detection module can be used in places that are susceptible to water or oil droplets, but it is not fully waterproof or oil resistant. Therefore, the overspeed detection module should not be placed or used in water or oil contaminated environments. If the servo motor is connected to a reduction gear, an oil seal should be added when using the overspeed detection module to prevent the oil from the reduction gear from entering the cable of the overspeed detection module and not immersing it in oil or water. The overspeed detection module cable ensures that the cable is not subjected to torque or vertical loads due to external bending forces or its own weight, especially at the cable outlet or connection. When the overspeed detection module is moving, the cable that is configured with the motor should be firmly fixed to a stationary part relative to the motor.
133388-01
And an additional cable installed in the cable support should be used to extend it, so that bending stress can be minimized. The bend radius of the cable should be as large as possible. The shaft end load allowed by the overspeed detection module ensures that the radial and axial loads applied to the servo motor shaft during installation and operation are controlled within the specified values of each model. Be extra careful when installing a rigid coupling, especially when excessive bending loads may cause damage or wear to the shaft end and bearings. It is best to use a flexible coupling to keep the radial load below the allowable value. This material is designed specifically for high mechanical strength overspeed detection modules. Regarding allowable axle load. When installing and disassembling the coupling components to the shaft end of the overspeed detection module, do not directly hit the shaft end with a hammer. The hammer directly strikes the shaft end, and the encoder on the other end of the servo motor shaft needs to be damaged. Efforts should be made to align the shaft end to the optimal state, which may cause vibration or bearing damage.
133388-01
There are no reviews yet.