KOLLMORGEN SERVOSTAR-310 伺服放大器在运输和储存过程中，博世力士乐交流电机应始终保持水平方向干燥，无任何负载。必须使用配有吊索的起重机进行运输。该产品符合DIN 42950规范的B5设计。在安装设备之前，应检查电机法兰支架，确保其无毛刺。必须使用四个M10螺钉以51Nm的拧紧力矩固定此法兰。只有在干燥和断电状态下，才能连接和断开装置的插头。
SERVOSTAR-310
干燥和断电状态下，才能连接和断开装置的插头。在使用电机时，必须将它们牢固地拧紧。KOLLMORGEN SERVOSTAR-310 伺服放大器在操作之前，必须正确对齐和安装电机。本产品的电气连接应按照制造商的规范进行。其电缆螺纹接头也必须拧紧。由于灰尘、污垢或刨屑过多，设备功能往往会受到不利影响。根据DIN ISO 281规范，该装置的轴承使用寿命为30000小时。
SERVOSTAR-310
该装置必须安装在海拔1000米的地方。该单位在造纸和食品加工行业运营。绝不应使其在温度变化剧烈的区域发挥作用。当电机处于静止模式时，其持续扭矩为12Nm。当电机法兰插座盖安装有密封空气接头时，必须检查产品的O形圈是否正确就位。该设备的电源连接器包括用于保持制动器和温度传感器的连接。该产品具有高过载能力KOLLMORGEN伺服模块因为从定子绕组到外壳外壁的散热效果理想。
SERVOSTAR-310、
During transportation and storage, the Bosch Rexroth AC motor of the KOLLMORGEN SERVOSTAR-310 servo amplifier should always be kept dry in the horizontal direction without any load. A crane equipped with a lifting sling must be used for transportation. This product complies with the B5 design of DIN 42950 specification. Before installing the equipment, the motor flange bracket should be inspected to ensure that it is free of burrs. Four M10 screws must be used to secure this flange with a tightening torque of 51Nm. Only connect and disconnect the plug of the device in a dry and power off state.
SERVOSTAR-310
Only connect and disconnect the plug of the device in a dry and power off state. When using motors, they must be securely tightened. The KOLLMORGEN SERVOSTAR-310 servo amplifier must be correctly aligned and installed with the motor before operation. The electrical connection of this product should be carried out in accordance with the manufacturer’s specifications. The cable threaded joints must also be tightened. Due to excessive dust, dirt, or shavings, equipment functionality is often adversely affected. According to the DIN ISO 281 specification, the bearing service life of this device is 30000 hours.
SERVOSTAR-310
The device must be installed at an altitude of 1000 meters. This unit operates in the papermaking and food processing industries. It should never be allowed to function in areas with drastic temperature changes. When the motor is in stationary mode, its continuous torque is 12Nm. When the motor flange socket cover is installed with a sealed air joint, it is necessary to check whether the O-ring of the product is correctly seated. The power connector of the device includes a connection for maintaining the brake and temperature sensor. This product has a high overload capacity KOLLMORGEN servo module because the heat dissipation effect from the stator winding to the outer wall of the casing is ideal.
There are no reviews yet.