联系我们 24/7+86 18859254943
联系我们 24/7+86 18859254943

PFSA145 3BSE008843R1测量张力配件现货

In stock

PFSA145 3BSE008843R1测量张力配件现货

  • 电话/Phone:17350011025 (微信同号)
  • 邮箱/Email:1713556114@qq.com
  • QQ:1713556114

PFSA145 3BSE008843R1测量张力配件现货

输入电压:12-48VDC输出相电流:2.2A(Peak)
3个数字信号输入口:脉冲/方向/使能信号,5-24VDC,光电隔离拨码开关选择,16档细分:200,400,800,1600,3200,6400,128
23oo,256oo ,
1000,2000,4000,5000,8000,10000,20000,25000;
拨码开关选择,8档电流:0.3A,0.5A,0.7A,1.0A,1.3A,1.6A,1.9A,2.2A,拨码开关选择负载惯量,以配合电流控制算法,使电机性能最优化
拨码开关选择脉冲方向输入口的滤波频率150KHz或2MHz
拨码开关选择是否启用内部细分功能
自动减流功能:50%或90%,拨码开关选择自检功能
保护:过压,欠压,过温,过流,电机绕组开路

压磁式传感器是利用磁性材料在机械力作用下导磁率发生变化的原理工作的。这种传感器由整块不锈钢制成,在不锈钢体上冲有四个孔。通过这四个孔缠绕有两组线圈,它们互成一定的角度。当在初级线圈中通以交变电流时,初级线圈中会产生磁场。因为初级和次级两组线圈是互成一定角度的,所以只要传感器上没有负载,次级线圈中就不会产生磁场。当在传感器的测量方向加以机械力时,初级线圈中的磁场传播方向发生变化,将次级线圈包容进了磁场。由于次级线圈中的磁场发生了变化,因此在该线圈中产生了感应电势。控制单元会将这个感应电势转换成一个与被测力对应成比例的直流电压信号。
FCL201C枕块式张力计垂直测压元件﹐采用圆柱形插头连接;测力范围:5~50KN;
PFCL201CDICE枕块式张力计垂直测压元件,采用电缆密封接头/带保护软管的固定电缆连接﹐测力范围:5~50KN;
PFTL 101A枕块式张力计同瑞达科技水平测压元件﹐圆柱插头连接﹐测力范围: 0.2~2KN.

信号匹配单元,又称天线共用双工器,是一个比较特殊的双向三端滤波装置。双工器是异频双工电台信道控制器的主要组成部分,其主要作用是将上行信号与下行信号相隔离,保证信道控制机的接收和发射能同时正常工作,它是由两组不同频率的阻带滤波器组成,避免本机发射信号传输到接收机。

Input voltage: 12-48VDC Output phase current: 2.2A (Peak)
3 digital signal input ports: pulse/direction/enable signal, 5-24VDC, photoelectric isolation dial switch selection, 16 level subdivision: 20040080016003206400128
23oo, 256oo,
10002000400050008001100002000025000;
Dip code switch selection, 8-speed current: 0.3A, 0.5A, 0.7A, 1.0A, 1.3A, 1.6A, 1.9A, 2.2A. Dip code switch selection load inertia to cooperate with current control algorithm to optimize motor performance
The DIP switch selects the filtering frequency of the pulse direction input port at 150KHz or 2MHz
Select whether to enable internal segmentation function with the dial switch
Automatic current reduction function: 50% or 90%, with self check function selected by the dial switch
Protection: overvoltage, undervoltage, over temperature, overcurrent, motor winding open circuit
Piezomagnetic sensors work by utilizing the principle that the permeability of magnetic materials changes under mechanical force. This sensor is made of a whole piece of stainless steel and has four holes punched on the stainless steel body. Two sets of coils are wound through these four holes, forming a certain angle with each other. When alternating current is applied in the primary coil, a magnetic field is generated in the primary coil. Because the primary and secondary coils are at a certain angle to each other, as long as there is no load on the sensor, no magnetic field will be generated in the secondary coil. When mechanical force is applied in the measurement direction of the sensor, the direction of magnetic field propagation in the primary coil changes, enclosing the secondary coil in the magnetic field. Due to changes in the magnetic field in the secondary coil, an induced electromotive force is generated in the coil. The control unit will convert this induced electromotive force into a DC voltage signal proportional to the measured force.
FCL201C pillow block tension meter vertical pressure measuring element, connected by a cylindrical plug; Force measurement range: 5~50KN;
PFCL201CDICE pillow block tension meter vertical pressure measuring element, connected by cable sealing joint/fixed cable with protective hose, measuring force range: 5-50KN;
PFTL 101A pillow block tension gauge is connected to the horizontal pressure measuring element of Ruida Technology with a cylindrical plug, with a force measurement range of 0.2~2KN
Signal matching unit, also known as antenna shared duplexer, is a relatively special bidirectional three terminal filtering device. The duplexer is the main component of the channel controller of the frequency difference duplex radio station. Its main function is to isolate the uplink signal from the downlink signal, ensuring that the reception and transmission of the channel control machine can work normally simultaneously. It is composed of two sets of stopband filters with different frequencies, avoiding the transmission of local transmission signals to the receiver.

Customers reviews

There are no reviews yet.

Be the first to review “PFSA145 3BSE008843R1测量张力配件现货”

您的邮箱地址不会被公开。 必填项已用 * 标注

Search for products

Back to Top
Product has been added to your cart