GE模拟输出模块 IC693ALG392

IC693ALG392 是一款适用于 PACSystems RX3i 和系列 90-30 的模拟电流/电压输出模块。该模块有八个单端输出通道，根据用户的安装提供电压输出和/或电流环路输出。每个通道都可以由配置软件生成后续范围（0 至 10 伏），如单、（-10 至 10 伏）双、0 至 20 毫安或 4 至 20 毫安。每个通道都能够转换 15 至 16 位。这取决于用户偏好的范围。所有八个通道每 8 毫秒新一次。

当处于当前模式时， IC693ALG392模块会向每个通道的CPU 报告开路故障。当系统电源受到干扰时，模块可以进入已知的后状态。如果外部电源连续施加到模块，每个输出将保持其后的值或根据配置重置为零。可以安装在 RX3i 或系列 90-30 系统的任何 I/O 插槽中。

IC693ALG392是PACSystems RX3i和90-30系列的模拟电流/电压输出模块。该模块有八个单端输出通道，根据用户的安装，带有电压输出和/或电流环路输出。每个通道可由配置软件为后续示波器(O至+10伏)生成单极、(-10至+10犬)双极、0至20毫安或4至20毫安。

这IC693ALG392在当前模式下，模块向CPU报告每个通道的开路故障。当系统电源受到千扰时，模块可以进入已知的zui后状态。如果外部电源持续施加到模块，每个输出将保持其zui后的值或根据配置重置为零。可以安装在RX3i或90-30系列系统的任何I/O插槽中。

该模块必须从直接连接到端子板的外部电源获得24VDC电源。每个输出通道都是单端的，出厂时调整至0.625ua，这可能会因电压而异。用户应注意，在存在恶劣RF干扰的情况下，电流输出的模块精度可能降低至+/-1%FS，电压输出的模块精度可能降低至+/-3%FS。还应注意，该模块必须固定在金属外壳中才能正常工作。

The IC693ALG392 is an analog current/voltage output module for the PACSystems RX3i and Series 90-30. The module has eight single-ended output channels that provide voltage outputs and/or current loop outputs depending on the user’s installation. Each channel can be configured by the software to generate subsequent ranges (0 to 10 volts) such as single, (-10 to 10 volts) dual, 0 to 20 mA, or 4 to 20 mA. Each channel is capable of converting 15 to 16 bits. This depends on the user’s preferred range. All eight channels are new every 8 milliseconds.

When in the current mode, the IC693ALG392 module reports an open-circuit fault to the CPU on each channel. The module can enter a known post state when system power is disturbed. If external power is continuously applied to the module, each output will hold its subsequent value or reset to zero as configured. It can be installed in any I/O slot on an RX3i or Series 90-30 system.

The IC693ALG392 is an analog current/voltage output module for the PACSystems RX3i and Series 90-30. The module has eight single-ended output channels with voltage outputs and/or current loop outputs depending on the user’s installation. Each channel can be generated by configuration software for subsequent oscilloscopes (O to +10 volts) single-pole, (-10 to +10 dogs) bipolar, 0 to 20 mA, or 4 to 20 mA.

This IC693ALG392 In the current mode, the module reports open-circuit faults for each channel to the CPU. The module can enter a known zui last state when the system power supply is subjected to a thousand disturbances. If external power is continuously applied to the module, each output will maintain its zui last value or reset to zero depending on the configuration. It can be mounted in any I/O slot on an RX3i or 90-30 series system.

The module must receive 24VDC power from an external power supply connected directly to the terminal block. Each output channel is single-ended and factory adjusted to 0.625ua, which may vary by voltage. The user should be aware that in the presence of harsh RF interference, the module accuracy may be reduced to +/-1%FS for current outputs and +/-3%FS for voltage outputs.It should also be noted that the module must be secured in a metal enclosure for proper operation.