IC698PSA350D DCS输入模块

IC698PSA350是PACSystem RX7i平台的一部分电源模块，目前由Emerson Automation负责，以前由GE智能平台(GEIP) 生产。此电源安装在RX7通用背板_上。它的输入电压范围为85至264 VAC 47至63 Hz和100-150 VDC,大输入功率为440瓦(典型值)和500瓦(大值)。它的大输出功率为350瓦，总共三(3) 个输出，例如5 VDC、12 VDC和-12 VDC,输出电流分别为0-60安培、0-12安培和0-4安培。
IC698PSA350是PACSystem RX7i控制器系列的高容量电源模块。该模块用于输送背板电源，该电源由模块用于激活内部电路并可操作。
此电源模块占用机箱的单个插槽，设计为仅安装在RX7i机架的插槽0中。
IC698PSA350的输入电源电压为85至264 VAC, 100-150 VDC,交流输入频率为47-63 Hz。该模块的额定电压为120/240 VAC和125VDC,输入功率要求为440瓦(典型值)和500瓦(大值)。当用于交流输入电源时，该电源模块的功率因数为0.99。
IC698PSA350是一个单插槽电源模块，安装在RX7i机架的左侧插槽或插槽0 上。它配有各种LED状态指示器，有助于识别模块的操作状
态。这些指示灯包括Field OK (现场正常)、OUTPUT OK (输出正常)和OVER TEMP (超温) LED. 内置保护电路(如过热和过压保护)提供给该电源模块以及气流保护。70 CFM强制空气冷风扇位于系统机箱下方，为电源模块提供冷却空气。如果检测到t流停止，OVER TEM LED指示灯将启动。
IC698PSA350电源有A系列和B系列版本。A系列电源内部安装有0.25 “x 1.25”保险丝,而B系列电源具有5 x 20 m保险丝。安装的保险丝为8A/250V保险丝。
IC698PSA350电源模块是RX7i系列的一部分，由GE Fanuc制造。该模块能够通过背板向模块发送逻辑电平信号。它的额定输出功率为350瓦。额定工作电压为120/240伏AC和125伏DC。电源模块以47至63赫兹之间的频率运行。模块的工作温度范围在0至60摄氏度之间。电源模块配有气流传感器，可轻松检测风扇故障或驱动器周围气流停止。如果出现任何一种情况，温度过高的L ED将亮起。使用模块外部的跳线可以启用或禁用传感器。

IC698PSA350D

IC698PSA350D

The IC698PSA350 is a power supply module that is part of the PACSystem RX7i platform, which is currently being handled by Emerson Automation and was previously manufactured by GE Intelligent Platforms (GEIP). This power supply
source is mounted on the RX7 universal backplane_. It has an input voltage range of 85 to 264 VAC, 47 to 63 Hz, and 100 to 150 VDC, and has a high input power of 440 watts (typical) and 500 watts (high). The IC698PSA350 has a high output power of 350 watts with a total of three (3) outputs such as 5 VDC, 12 VDC, and -12 VDC with output currents of 0-60 amps, 0-12 amps, and 0-4 amps respectively.
The IC698PSA350 is a high-capacity power supply module for the PACSystem RX7i controller family. This module is used to deliver backplane power, which is used by the module to activate internal circuitry and is operable.
This power module occupies a single slot in the chassis and is designed to be installed only in slot 0 of the RX7i rack.
The IC698PSA350 has an input power supply voltage of 85 to 264 VAC, 100-150 VDC, and an AC input frequency of 47-63 Hz. The module is rated for 120/240 VAC and 125 VDC, and has an input power requirement of 440 watts (typical) and 500 watts (large). The power module has a power factor of 0.99 when used for AC input power.
The IC698PSA350 is a single-slot power supply module that mounts in the left slot or slot 0 of the RX7i rack. It is equipped with various LED status indicators to help identify the module’s operational status.
It is equipped with various LED status indicators to help identify the module’s operating status. These include the FIELD OK, OUTPUT OK, and OVER TEMP LEDs. Built-in protection circuits (such as over-temperature and over-voltage protection) are provided to the power supply module as well as airflow protection.70 The CFM forced-air cooling fan, located under the system chassis, provides cooling air to the power supply module. The OVER TEM LED indicator will activate if a t-stream stop is detected.
The IC698PSA350 power supply is available in Series A and Series B versions. The Series A power supply has an internal 0.25″ x 1.25″ fuse, while the Series B power supply has a 5 x 20 m fuse. The fuses installed are 8A/250V fuses.
The IC698PSA350 power supply module is part of the RX7i series, manufactured by GE Fanuc. The module is capable of sending logic level signals to the module through the backplane. It has a rated output power of 350 watts. The rated operating voltage is 120/240 volts AC and 125 volts DC.The power module operates at a frequency between 47 and 63 Hz. The module’s operating temperature range is between 0 and 60 degrees Celsius. The power supply module is equipped with an airflow sensor that easily detects a fan failure or stoppage of airflow around the drive. If either condition occurs, the Over Temperature L ED will illuminate. The sensor can be enabled or disabled using a jumper on the outside of the module.